Shindaiwa EC7600 Instrukcja Operatora Strona 9
- Strona / 84
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
9
WARNING!
Keep well away from fire!
Push the decompression valve In.
Pull the choke all the way out (choke
closed). The throttle will automatically
be set to fast idle. See Figure 10.
Place the unit on firm ground.
Secure the unit by placing your right
foot inside the rear handle and your left
hand on the front handle. See Figure 11.
3.
4.
5.
6.
Figure 11
Before starting the engine, place
the unit on a clean, level surface.
Make sure you have good secure
footing and always keep a firm grip
on the unit.
Move at least 3 meters away from
the fueling site before starting the
engine.
Make sure the cut-off wheel is
well clear of obstacles. The cut-off
wheel may rotate when the engine
starts.
Keep bystanders well away.
Never start the engine without a
cut-off wheel installed.
■
■
■
■
■
Starting a cold engine
Figure 10
Primer
Pump
Choke
Turn the on-off switch On.
Depress the primer pump a few times
repeatedly until the primer pump is
almost filled with fuel. See Figure 10.
1.
2.
When the engine fires, push the choke
in to its original position (choke open).
If the engine does not continue to run,
pull the recoil again.
As the engine starts, clear excess fuel
from the combustion chamber by rev-
ving the engine several times.
Let the engine run at idle speed for 2-3
minutes to warm up.
9.
10.
11.
12.
CAUTION!
The recoil starter can be damaged
by abuse.
Never pull the starter cord to its full
length.
Always engage the starter before
cranking the engine.
Always rewind the starter cord
slowly. Do not just let go of the cord.
■
■
■
■
IMPORTANT!
The throttle trigger can not be moved
without first depressing the lockout lever.
Operating the throttle will automatically
disengage the fast idle setting.
WARNING!
Grip the recoil starter handle with your
right hand, pull the starter cord slowly
until you feel the starter engage, then…
…start the engine by pulling the starter
cord upward rapidly.
7.
8.
Turn the on-off switch On.
Push the decompression valve in.
Pull the choke all the way out and push
it back to the original position (choke
open). The throttle is automatically set
at a fast idle position.
1.
2.
3.
Starting the engine
If the engine doesn’t start
WARNING!
The cut-off wheel must not
rotate at idle speed. If it rotates,
reduce idle speed by adjusting the
idle adjust screw.
Follow Steps 5 though 12, Starting a
Cold Engine.
4.
If the engine fails to start, repeat the
appropriate starting procedure for a cold
or warm engine.
Starting a warm engine
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji