Shindaiwa EC7600 Instrukcja Operatora Strona 16
- Strona / 84
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
EC7500.42
16
WARNING!
Make sure the replacement
cut-off wheel rpm rating is greater
than the speed indicated on the
wheel guard label.
WARNING!
Using the wrong size collar
may lead to failure of the wheel or the
unit and could result in serious injury.
Make sure the ignition switch is Off and
the engine is stopped.
Insert a 6mm hex wrench into the hole
in the belt guard to prevent the drive
shaft from turning. See Figure 29.
Loosen the outer flange bolt with the
wrench and remove the bolt and outer
flange.
Before mounting a cut-off wheel, deter-
mine its arbor diameter. If necessary,
remove the snap ring from the arbor,
install the correct collar, then re-install
the snap ring.
1.
2.
3.
4.
Figure 29
Outer
Flange
Remove the old wheel and install the
new one. Make sure the inner bore is
properly set onto the collar.
5.
Belt Guard
Hex Wrench
Outer
Flange
Bolt
Wrench
Tighten
Loosen
CAUTION!
Make sure the rotating direction of
wheel corresponds to the one indicated
on the wheel guard. Make sure there is
no dust around the outer flange.
Label Showing
Direction of
Rotation
Label Showing Rated
and Maximum Spindle
Speed
Wheel Guard
Diamond
Wheel
Replacing the Cut-off Wheel
Figure 31
Hooked Wire
Fuel Filler
Cap
Fuel Filter
Inspection and Maintenance (continued)
Replacing the Cut-off Wheel
Replace the outer flange and bolt, then
holding the hex wrench in the hole of
the belt guard, tighten the bolt with the
wrench.
Make sure the cut-off wheel is securely
fastened and does not wobble.
6.
7.
Figure 30
While running the engine at low speed,
make about 10 passes at cutting a concrete
block or a soft brick. Keep the block
watered while sharpening.
Sharpening a Diamond Cut-off Wheel
WARNING!
KEEP AWAY FROM FIRE
OR EXCESS HEAT!
CAUTION!
Make sure the fuel line is not pierced
by the hooked wire. The fuel line can
be easily damaged.
Remove the fuel filler cap.
Take the filter out from the fuel opening
by using a hooked wire. If the filter is
hard and clogged with debris, replace it
with a new one. See Figure 31.
1.
2.
Checking the Fuel Filter
Put the filter back into the fuel tank.
Make sure the fuel tube is not bent and
the filter stays at the bottom of the tank.
Put the fuel filler cap back and tighten it
securely.
3.
4.
- EC7500/EC7600 1
- ENGINE CUTOFF SAW 1
- Introduction 2
- Attention Statements 2
- Contents 2
- Safety Precautions 3
- Figure 1 4
- Figure 2 4
- Figure 3 4
- Safety Labels 5
- Unit Description 6
- Specifications 6
- Prior to assembly 7
- Mounting the Cut-off Wheel 7
- Mixing fuel 8
- Filling the fuel tank 8
- Starting a cold engine 9
- If the engine doesn’t start 9
- Starting a warm engine 9
- Stopping the Engine 10
- Wet or Dry Operation 11
- Adjusting Wheel Guard Angle 11
- Operating (continued) 12
- EC7500.48 13
- Cleaning the Air Cleaner 13
- Figure 24 14
- Figure 23 14
- Adjusting Belt Tension 15
- Replacing the Drive Belt 15
- Checking the Cut-off Wheel 15
- EC7500.42 16
- Replacing the Cut-off Wheel 16
- Checking the Fuel Filter 16
- Spark Arrester Maintenance 17
- Troubleshooting Guide 18
- DECLARATION 19
- CONFORMITY 19
- DÉCOUPEUSE THERMIQUE 23
- Mises en garde 24
- Table des matières 24
- Consignes de sécurité 25
- Consignes de sécurité (suite) 26
- Étiquettes de sécurité 27
- Description de l’appareil 28
- Caractéristiques techniques 28
- Avant l’assemblage 29
- Exemples de quantités de 30
- Démarrage d’un moteur froid 31
- Si le moteur ne démarre pas 31
- Démarrage d’un moteur chaud 31
- Arrêt du moteur 32
- Démarrage du moteur (suite) 32
- Fonctionnement 33
- Fonctionnement (suite) 34
- Nettoyage du filtre à air 35
- Figure 25 37
- Figure 26 37
- Figure 27 37
- Figure 28 37
- AVERTISSEMENT ! 38
- Entretien du pare-etincelles 39
- Guide de dépannage 40
- DÉCLARATION 41
- CONFORMITÉ 41
- REMARQUES : 42
- MOTOTRONCATRICE 45
- Sommario 46
- Messaggi informativi 46
- Introduzione 46
- Precauzioni di sicurezza 47
- Etichette di sicurezza 49
- Descrizione dell’attrezzo 50
- Specifiche tecniche 50
- Montaggio del disco da taglio 51
- Prima dell’assemblaggio 51
- Rifornimento del serbatoio 52
- Avviamento del motore a caldo 53
- Se il motore non si avvia 53
- Avviamento del motore (cont.) 54
- Arresto del motore 54
- Funzionamento 55
- Funzionamento (cont.) 56
- Pulizia del filtro dell’aria 57
- Figura 23 58
- Figura 24 58
- Controllo del disco da taglio 59
- AVVERTENZA! 60
- Figura 32 61
- Figura 33 61
- Risoluzione dei problemi 62
- DICHIARAZIONE 63
- DI CONFORMITÀ 63
- Italiano 64
- TRENNSCHLEIFER 65
- Einführung 66
- Wichtige Hinweise 66
- Vorsichtsmaßnahmen 67
- Abbildung 1 68
- Abbildung 2 68
- Arbeiten Sie immer unter 68
- Brusthöhe 68
- Abbildung 3 68
- Sicherheitsaufkleber 69
- Technische Daten 70
- Gerätebeschreibung 70
- Vor dem Zusammenbau 71
- Montieren der Trennscheibe 71
- Beispiele für 72
- Kaltstart des Motors 73
- Warmstart des Motors 73
- Ausschalten des Motors 74
- Trennschleifen 75
- Nass- oder Trockenbetrieb 75
- Betrieb (Fortsetzung) 76
- Reinigen des Luftfilters 77
- Abbildung 23 78
- Abbildung 24 78
- Einstellen der Riemenspannung 79
- Überprüfen der Trennscheibe 79
- Auswechseln der Trennscheibe 80
- Schmieren des Kupplungslagers 81
- Fehlerbehebung 82
- KONFORMITÄTSERKLÄRUNG 83
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji